 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| UNISONIC TECHNOLOGIES CO., LTD PA0202 2-W STEREO AUDIO POWER AMPLIFIER WITH MUTE DESCRIPTION The UTC PA0202 is a monolithic integrated circuit that stereo bridged audio power amplifiers capable of producing 2 W into 3 with a 5V supply voltage or 800mW into 3 with a 3.3V supply voltage .The UTC PA0202 simplifies design and frees up board space for other features. Both of the depop circuitry and the thermal shutdown protection circuitry are integrated in UTC PA0202, that reduce clicks and pops noise during power up or shutdown mode operation. A MUX control terminal (HP/LINE) allows selection between the two sets of stereo input signals. To simplify the audio system design, UTC PA0202 combines a stereo bridge-tied loads (BTL)mode for speaker drive and a stereo single-end (SE)mode for headphone drive into a single chip, where both modes are easily switched by the SE/BTL input control pin signal. CMOS IC HTSSOP-24 *Pb-free plating product number: PA0202L FEATURES * Improves depop circuitry to eliminate turn-on and turn-off transients in output * Output power: -2W(typ.)@5V into 3 with 0.2% THD+N max (1kHz) -800mW(typ.)@3.3V into 3 with 0.2% THD+N max (1kHz) * Fully specified for use with 3- Loads * Stereo switchable bridged/single-ended power amplifiers * Input MUX select terminal * Thermal-shutdown protection * Shutdown mode available ORDERING INFORMATION Normal PA0202-N24-R PA0202-N24-T Order Number Lead Free Plating PA0202L-N24-R PA0202L-N24-T Package HTSSOP-24 HTSSOP-24 Packing Tape Reel Tube PA0202L-N24-R (1)Packing Type (2)Package Type (3)Lead Plating (1) R: Tape Reel, T: Tube (2) N24: HTSSOP-24 (3) L: Lead Free Plating, Blank: Pb/Sn www.unisonic.com.tw Copyright (c) 2005 Unisonic Technologies Co., Ltd 1 of 11 QW-R502-106,A PA0202 PIN CONFIGURATION GND/HS TJ LOUT+ LLINEIN LHPIN LBYPASS LVDD SHUTDOWN MUTE OUT LOUTMUTE IN GND/HS 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 GND/HS NC ROUT+ RLINEIN RHPIN RBYPASS RVDD NC HP/LINE ROUTSE/BTL GND/HS CMOS IC PIN DESCRIPTION PIN NO 1, 12, 13, 24 6 17, 23 19 4 5 7 8 9 11 14 16 18 20 21 2 3 10 22 15 PIN NAME GND/HS LBYPASS NC RBYPASS LLINE IN LHP IN LVDD SHUTDOWN MUTE OUT MUTE IN SE/BTL HP/LINE RVDD RHPIN RLINEIN TJ LOUT+ LOUTROUT+ ROUTI/O DESCRIPTION Power ground; directly connected to thermal pad. Tap to left channel internal mid-supply voltage divider bias No connection Tap to right channel internal mid-supply voltage divider bias Left channel line input; selected when HP/LINE is held low Left channel headphone input; selected when HP/LINE is held high Left channel power supply and for primary bias circuits Places entire IC in shutdown mode when held high, IDD = 5A Follows MUTE IN, provides buffered output Mute all amplifiers input; high active to mute amplify, low active to normal operation SE & BTL mode selection; active high for SE mode, active low for BTL mode MUX control input, active high to select headphone input, active low to select line input Right channel power supply Right channel headphone input, selected when HP/LINE is held high Right channel line input, selected when HP/LINE is held low Sources current proportional to the junction temperature. Left floating for normal operation. Left channel + output in BTL & SE mode Left channel - output in BTL mode & high-impedance in SE mode Right channel + output in BTL & SE mode Right channel - output in BTL mode & high impedance in SE mode I I I I I I I I I I I O O O O O UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 11 QW-R502-106,A PA0202 BLOCK DIAGRAM CMOS IC RLINEIN RHPIN RBYPASS Right MUX ROUT+ ROUTRVDD MUTE IN MUTE OUT SHUTDOWN Bias, Thermal Shutdown Logic Control SE/BTL HP/LINE LVDD LBYPASS LHPIN LLINEIN Left MUX LOUT+ LOUT- UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 11 QW-R502-106,A PA0202 ABSOLUTE MAXIMUM RATINGS (unless otherwise specified) CMOS IC PARAMETER SYMBOL RATINGS UNIT Supply Voltage VDD 6 V Input Voltage VIN -0.3~VDD ~+0.3 V Continuous Total Power Dissipation PD Internally limited Junction Temperature TJ +150 Operating Temperature TOPR -40 ~ +85 Storage Temperature TSTG -65 ~ +150 Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. RECOMMENDED OPERATING CONDITIONS PARAMETER Supply Voltage SYMBOL VDD 4- stereo BTL VDD = 5 V, drive, 250 mW/ch with proper PCB average power, design 3- stereo BTL VDD = 5 V, drive, 2 W/ch average with proper PCB power, design VDD=5V VDD=3.3V MIN 3 -40 NOM 5 MAX UNIT 5.5 V 85 Operating Temperature TOPR -40 1.25 1.25 85 4.5 2.7 Common Mode Input Voltage VICM V DC ELECTRICAL CHARACTERISTICS (TA = 25 ) PARAMETER SYMBOL TEST CONDITIONS Stereo BTL Stereo SE VDD=5V Mono BTL Mono SE Stereo BTL Stereo SE VDD=3.3V Mono BTL Mono SE MIN TYP(1) 19 9 9 3 13 5 5 3 5 1 5 MAX 30 18 18 10 20 10 10 6 25 19 UNIT mA Supply Current IDD mA Output Offset Voltage VO(OFF) VDD = 5 V, Gain = 2, See Note 1 (Measured Differentially) Supply Current in Mute Mode IDD(MUTE) VDD=5V IDD in Shutdown IDD(SD) VDD=5V Note 1. At 3 V < VDD < 5 V the dc output voltage is approximately VDD/2. mV mA A UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 4 of 11 QW-R502-106,A PA0202 AC OPERATING CHARACTERISTICS VDD = 5 V, TA = 25 , RL = 3 PARAMETER SYMBOL TEST CONDITIONS Output Power (Each Channel) See THD =0.2% BTL POUT Note 2 THD =1% BTL Total Harmonic Distortion Plus POUT = 2 W, f = 20 ~20 kHz TDH+N Noise VIN = 1V, RL=10K, AV=1V/V Maximum Output Power Bandwidth BW AV = 10 V/V ,THD < 1 %, Phase Margin RL = 4 , Open Loop, f = 1 kHz Supply Ripple Rejection Ratio RR f = 20~20kHz, Mute Attenuation Channel-to-Channel Output f = 1 kHz Separation Line/HP Input Separation BTL Attenuation in SE Mode Input Impedance ZIN Signal-to-Noise Ratio POUT =500mW, BTL Output Noise Voltage eN VDD = 3.3 V, TA = 25 , RL = 3 PARAMETER SYMBOL TEST CONDITIONS Output Power ( Each Channel) See THD =0.2% BTL POUT Note 2 THD =1% BTL Total Harmonic Distortion Plus POUT = 800mW, f = 20 ~20 kHz TDH+N Noise VIN = 1V, RL=10K, AV=1V/V Maximum Output Power Bandwidth BW AV = 10 V/V, THD < 1 %, Phase Margin RL = 4 , Open Loop f = 1 kHz Supply Ripple Rejection Ratio RR f = 20~20kHz, Mute Attenuation Channel-to-Channel Output f = 1 kHz Separation Line/HP Input Separation BTL Attenuation in SE Mode Input Impedance ZIN Signal-to-Noise Ratio POUT =500mW, BTL Output Noise Voltage eN Note 2. Output power is measured at the output terminals of the IC at 1 kHz. MIN TYP 2 2.2 200 100 >20 85 80 60 85 85 100 100 2 95 21 MIN TYP 800 900 350 200 >20 85 70 55 85 85 100 100 2 95 21 CMOS IC MAX UNIT W m% m% KHz dB dB dB dB dB M dB V(RMS) MAX UNIT mW m% m% KHz dB dB dB dB dB M dB V(RMS) UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 11 QW-R502-106,A PA0202 TYPICAL APPLICATION CIRCUIT RFR 50K CMOS IC CFR 5 pF RIR 10K CIR 1F NC RLINEIN RHPIN Right MUX ROUT+ ROUTRVDD V DD CS 0.1 F 100K ( see Note ) SE/BTL 100K HP/LINE Bias, Thermal Shutdown LVDD VDD 1K COUTL 330 F 0.1 F COUTR 330 F 1K RBYPASS CB 1F System Control MUTE IN MUTE OUT SHUTDOWN Logic Control LBYPASS CIL 1F RIL 10K NC LHPIN LLINEIN Left MUX LOUT+ LOUT- RFL 50K CFL 5 pF N ote : 0. 1 F ceramic capacitor should be placed as close as possible to the IC For filtering lower . frequency noise signals, a larger aluminum electrolytic capacitor of10 F or greater should be placed near the audio power amplifier . PA0202 Minimum Configuration Application Circuit UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 11 QW-R502-106,A PA0202 TYPICAL APPLICATION CIRCUIT CMOS IC RFRHP 10K RFRLINE 50K CFRLINE 5pF CIRLINE RIR LINE 1F 10K RLINEIN RHPIN Right MUX ROUT+ ROUTRVDD VDD CSR 0.1F 100K (see Note 2) SE/BTL 100K HP/LINE Bias, Thermal Shutdown LVDD 0.1F COUTR 330F 1K CIRHP 1F RIRHP 10K RBYPASS C BR 0.1F MUTE IN MUTE OUT Logic Control System Control see Note 1 SHUTDOWN CILHP R ILHP 1F 10K LBYPASS CBL 1F LHPIN LLINEIN Left MUX LOUT+ LOUT- VDD CSR 0.1F (see Note 2) 1K COUTL 330F CILLINE 1F RILLINE 10K R FLLINE 50K CFLLINE 5pF RFLHP 10K Note:1. This connection is for ultra-low current in shutdown mode . 2. A 0.1 F ceramic capacitor should be placed as close as possible to the ICFor filtering lower. frequency noise signals a larger aluminum electrolytic capacitor of10 F or greater should be , placed near the audio power amplifier . PA0202 Full Configuration Application Circuit UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 7 of 11 QW-R502-106,A PA0202 TYPICAL CHARACTERISTICS Total Harmonic Distortion Plus Noise vs Frequency 10 VDD=5V RL=4 AV=-2V/V BTL 1 POUT=1.5W POUT=2W, RL=3 POUT=0.75W CMOS IC THD+N -Total Harmonic Distortion + Noise (%) THD+N -Total Harmonic Distortion + Noise (%) Total Harmonic Distortion Plus Noise vs Output Power 10 VDD=5V RL =3 BTL 1 f=20KHz f=20Hz f=1KHz 0.1 0.1 POUT=0.25W 0.01 20 100 1K Frequency, f (Hz) 10K20K 0.01 0.01 0.1 1 Output Power, POUT (W) 10 THD+N -Total Harmonic Distortion + Noise (%) 1 THD+N -Total Harmonic Distortion + Noise (%) Total Harmonic Distortion Plus Noise vs Frequency 10 VDD=5V RL=8 SE Total Harmonic Distortion Plus Noise vs Output Power 10 VDD=5V RL =8 SE 1 f=20KHz 0.1 POUT=0.25W POUT=0.1W PO=0.05W 100 1K Frequency, f (Hz) 10K20K 0.1 f=1KHz 0.01 20 0.01 f=100Hz 0.001 0.01 0.1 Output Power, POUT (W) 1 THD+N -Total Harmonic Distortion + Noise (%) 1 THD+N -Total Harmonic Distortion + Noise (%) Total Harmonic Distortion Plus Noise vs Frequency 10 VDD=5V R L=32 SE Total Harmonic Distortion Plus Noise vs Output Power 10 VDD=5V RL =32 SE 1 f=20KHz 0.1 POUT=75mW POUT=20mW 0.1 f=20Hz 0.01 20 POUT=25mW 100 1K 10K20K Frequency, f (Hz) 0.01 0.001 f=1KHz 1 0.01 0.1 Output Power, POUT (W) UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 8 of 11 QW-R502-106,A PA0202 TYPICAL CHARACTERISTICS(Cont.) Output Noise Voltage vs Frequency CMOS IC Output Noise Voltage, Vn (v) (rms) VDD=5V BW=22Hz~22KHz R L=4 VOUT BTL VOUT + Supply Ripple Rejection Ratio (dB) 100 0 -10 RL=4 =4.7F -20 CB BTL -30 -40 -50 -60 -70 -80 Supply Ripple Rejection Ratiovs Frequency 10 VOUT - VDD=3.3V 1 20 100 1K 10K 20K Frequency, f (Hz) -90 -100 20 VDD=5V 100 1K Frequency, f (Hz) 10K 20K Supply Ripple Rejection Ratio (dB) Crosstalk (dB) 0 -10 R L=4 C B=4.7F -20 SE -30 -40 -50 -60 -70 -80 Supply Ripple Rejection Ratiovs Frequency -40 -50 -60 -70 -80 -90 -80 -110 100 1K Frequency, f (Hz) 10K 20K -120 20 Crosstalk vs Frequency VDD=5V POUT=1.5W R L=4 BTL LEFT TO RIGHT VDD=5V VDD=3.3V RIGHT TO LEFT -90 -100 20 100 1K Frequency, f (Hz) 10K 20K Crosstalk vs Frequency -40 -50 -60 VDD=5V POUT=75mW RL =32 SE Crosstalk (dB) Gain (dB) -70 -80 -90 -80 LEFT TO RIGHT 5 4 3 2 1 0 20 Phase -135 -180 -225 -110 RIGHT TO LEFT -120 20 100 1K Frequency, f (Hz) 10K 20K 100 -270 1K 10K 100K 1M Frequency, f (Hz) 9 of 11 QW-R502-106,A UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw Phase Closed-Loop Response 10 V =5V DD 9 POUT=1.5W 8 AV=-2V/V BTL 7 Gain 6 0 -45 -90 PA0202 TYPICAL CHARACTERISTICS(Cont.) Output Power vs Load Resistance 3 THD=N=1% BTL Each Channel 1 CMOS IC Output Power vs Load Resistance THD=N=1% SE Each Channel Output Power, POUT (W) 2 VDD=5V Output Power, POUT (W) 2.5 0.8 0.6 0.4 0.2 0 0 VDD=3.3V 4 1.5 1 VDD=5V 0.5 0 0 VDD=3.3V 8 16 24 32 40 48 56 Load Resistance RL ( ) , 64 8 12 16 20 24 28 Load Resistance RL ( ) , 32 Power Dissipation vs Output Power 1.8 Power Dissipation, PD (W) Power Dissipation vs Output Power 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 RL=8 VDD=3.3V BTL Each Channel 0.5 0.25 0.75 Output Power, POUT (W) R L=4 RL=3 1.6 Output Power, PD (W) RL =3 1.4 1.2 1 0.8 0.6 0.4 0.2 0 0 R L=4 RL =8 f=1KHz BTL Each Channel 1 1.5 0.5 2 Output Power, POUT (W) 2.5 0 1 Power Dissipation vs Output Power 0.8 Power Dissipation, PD (W) Power Dissipation, PD (W) Power Dissipation vs Output Power 0.6 0.6 RL=4 0.4 RL=4 0.4 R L=8 RL=8 0.2 VDD=3.3V SE Each Channel 0.25 0.2 RL =32 0 0 VDD=5V SE Each Channel 0.4 0.5 0.6 0.1 0.2 0.3 Output Power, POUT (W) 0 0 RL =32 0.2 0.05 0.1 0.15 Output Power, POUT (W) UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 10 of 11 QW-R502-106,A PA0202 CMOS IC UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 11 of 11 QW-R502-106,A |
Price & Availability of PA0202-N24-R
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |